For the basic overview of the project, click here.
- Linksys WRT54G Wireless Router ($70; various sources online)
- Linksys WRE54G Wireless Range Expander ($100; various sources online)
- Radio Shack Universal low power DC power adapter (pn: 273-1811) with 3 volt selector ($23; radioshack.com)
- Radio Shack 12 VDC Adapter Accessory Outlet (pn: 270-1527) ($7.49; radioshack.com)
- Solar Panel, at least 10-watts and 14-volts ($119; sundancesolar.com)
- Water resistant outdoor enclosure, 9" x 6.1" x 3.1" (pn: MC-ENC-196YG) ($12.91; defactowireless.com)
- Pacific Wireless 9 dBi 2.4 GHz vertically polarized omni-directional antenna with N-female connector (pn: OD24-9) ($57.95; wlanparts.com)
- 12 volt sealed lead acid battery with spade terminals (7 Amp-hour) ($21.99)
- 24-inch pigtail cable with N-Male connector ($14.95)
- 18-gauge wire, black and red - ($5)
- Female insulated quick-disconnect connectors, crimp-type, sized for battery spade terminals ($3)
- In-line fuse holder ($7)
- 10-amp fuse (50 cents)
The following parts are available at any electronics or hardware store:
- Soldering iron, solder, solder wick
- Wire stripper, cutters
- Long nose pliers
- Electrical tape
- Xacto knife or razorblade
- Insert the CD for the Linksys WRT54G access point (AP) and follow the instructions for connecting it to your DSL or cable router. Assign an SSID (network name) and WPA pass key using the Setup Wizard.
- Insert the CD for the Linksys WRE54G Range Expander and follow the instructions for associating it with the AP you set up in Step 1. Do this near the AP; we will move it outdoors once it´s associated.
- Unplug the Range Expander and remove the power cord from rear of case.
- Remove the four rubber feet and unscrew the four screws under the feet to pull apart the case. , )
- Unclip the main circuit board and power supply board from the bottom half of the case.
- Remove brown and blue power plugs entering bottom of case.
- Unplug the black and red wires from the brown power supply board. We will no longer use the power board.
- De-solder the antenna from the circuit board. Note how the antenna was connected (outer shield to grounding pads, center conductor to signal pad.)
- Using long nose pliers, unclip the antenna from the top half of the case. We will no longer use that antenna.
- Feed the DC-to-DC converter plug and the N-female pigtail through the opening you just made by removing the stock antenna. Also feed the pigtail through the opening of the outdoor enclosure.
- Strip and prepare the antenna pigtail. Make sure the shield is pulled back from the center conductor and the two are not touching.
- Solder the antenna pigtail to the circuit board. Solder the shield into place first, then bend the center conductor into place and solder that down. You may wish to use an Xacto knife to expose the copper ground plane to help make a larger surface upon which to solder the outer shield.
- Use an ohmmeter to ensure the shield is not shorting to the center conductor. Resistance should be infinite between the center conductor and the outer shield.
Prepare the repeater:
Install the Antenna:
Prepare Charging Circuit Power:
- Strip the ends of the wires coming from the solar panel, the ends of the cigarette lighter socket, and two lengths of red and black wire. Run the solar panel wires through the opening of the enclosure before soldering.
- Install a fuse holder and a 10-amp fuse near the negative (â€) terminal of the battery.
- Create a three-way connection between the negative lines and, separately, the positive lines connecting the cigarette lighter socket, the solar panel, and the battery to each other. Remember to always keep positive (red) to positive, and negative (black) to negative. Cover exposed wire with electrical tape to prevent shorts.
- Switch the DC-to-DC converter to the 3-volt setting. Using a higher voltage may burn out or otherwise damage the repeater.
- Plug the DC-to-DC converter into the cigarette lighter socket and use a voltmeter to check for power by placing the black lead on the negative (â€) terminal of the battery and the red lead on one of the two power ports of the converter. You should see 0 volts on one port and +3 volts on the other. Mark â€ and + on the connector and unplug the converter for now.
- Cut the four red & black wires leaving about two inches from the end to the circuit board connector. Strip the ends of all four of them.
- Twist the black wires together and, separately, twist the red wires together and solder them. (Black to black. Red to red.) You should have one black lead and one red lead.
- Insert the wires into the DC-to-DC converter and solder them into place. Make sure you put black to the negative (â€) side and red to the positive (+) side that you marked in Step 18.
- Close and screw the case back together.
- Place the battery at the bottom of the case. Attach the repeater to the inside using tape or Velcro.
- Ensure the DC-to-DC converter is still set to 3 volts and plug it into the cigarette lighter socket.
- If everything is connected, the repeater will power on and associate with the AP again (see Step 2). Find a location (away from your sprinklers) to mount the enclosure and antenna. This enclosure is water resistant and should stay dry in the rain, but it´s not waterproof.
- Mount the solar panel so it is exposed to the sun throughout the day. If you want to be really energy efficient, you can mount the panel so sunlight hits it directly at high noon. For most installations, tilt the panel at a 45-degree angle. If you are located at a latitude higher than 45 degrees from the Earth's equator, use 60 degrees or more. If you are on the equator, point it straight up at 0 degrees.
Prepare Repeater Power:
Button up and turn it on:
For more on understanding and preparing cables, pigtails, and connectors, download Chapter 1 (PDF) of Outmesguine's book Wi-Fi Toys.
Solar paneled backyard network., awesome ideas! I love the fact that most people are thinking this way these days. My brother and I actually just got done building our own solar panel set. It was great, not even that hard!
- Brett Adams
Hello Brett Adams,
I like to develop Solar paneled backyard network( solar wifi extender). Kindly help me in this project . Please send me the circuit diagrams of connections used . My mail Id is : firstname.lastname@example.org.